Колт М-16 или АК-47

Тук може да поставите своя проблем за решаване ако не може да се справите или просто искате още едно мнение

Модератори: dcv, ilu6a

с какво работите

рН
0
Няма гласували
Общи киселини
1
20%
Нищо
4
80%
 
Общо гласове : 5

Колт М-16 или АК-47

Мнениеот vinoirakia » Съб Юни 28, 2008 6:39 am

А сега де.

Среща между старото и новото.

След една седмица пояснявам, но дотогава ще сте разбрали това което искам да кажа.

Winemaking at High pH
by Clark Smith
In this section, we consider the winemaking terrain above pH 3.6. Since the standards for most California wines that exist today (though not necessarily tomorrow) make it difficult to produce commercially acceptable white wines, this is essentially a discussion of red wine production. Consumer expectations for red wine differ from whites in several salient ways:
• More tolerance of browning
• Less emphasis on clarity
• Less emphasis on fresh fruitiness
• More value placed on complexity, less on cleanliness of aroma
• Greater ageability requirements
The dominant theme of low pH winemaking is focused on prevention and control. In high pH winemaking, we often acknowledge that we have given up on prevention, and try instead to direct the inevitable to a stable and agreeable outcome.
SECTION 1: STABILITY
The microbiological triangle considers the three requirements of Inoculum, Nutrients, and Inhibitors. Any one of these elements may be addressed to control an organism's growth, as long as the ecology of a specific organism is understood. When blending, it is important to consider that two stable wines, when combined, may supply missing elements required for spoilage. The utility of these elements in the high pH realm is entirely different from the low pH environment.
I. Inhibitors:
SO2
In low pH winemaking, we have stressed the role of molecular sulfur dioxide to control the growth of microorganisms. Since its effectiveness as a inhibitor is greatly lessened at high pH, it is more sensible to speak in terms of free and total SO2.
Free SO2, which is substantially all bisulfite, should be maintained to inhibit oxidation and to combine with aldehyde as it is formed through chemical oxidation of EtOH and by the action of film yeasts. When oxygen enters a red wine, it reacts with phenolics and promotes their polymerization. A side product of this reaction is hydrogen peroxide, which may be damaging to wine flavor and can oxidize ethanol. Its reaction with SO2, however, occurs much faster, so a small amount (say 10 to 30 ppm) bisulfite is extremely effective in scavenging peroxide. Since SO2 is depleted by this action and by aldehyde binding, it must be measured by aeration/oxidation and maintained at a reasonable level throughout ageing.
A desirable consequence of sulfite oxidation to sulfate is the liberation of a titratable proton, with the effect that over time, very high pH wines tend to experience increased TA and decreased pH. This effect is proportional to the sulfite concentration, which is ten times higher at pH 4.0 than at pH 3.0, and can thus be ignored below 3.6, but can, during extended barrel age at pH 3.9, result in an increase of as much as 1 g/L in TA and in sulfate concentration (see below for flavor effects) and a reduction of 0.1 or more in pH.
Total SO2 should be measured to assess flavor impact (a soapy finish can be detected at about 200 ppm) and because of its inhibitory effect on malolactic bacteria at about 100 ppm.
Addition of SO2 to young wine will be observed to bleach monomeric pigment. This is a reversible reaction, and actually stabilizes red color by maintaining a pool of monomeric pigment, which is restored to the wine as it ages and the pigments polymerize.
Temperature
Since at high pH, SO2 is not very effective in inhibiting spoilage organisms, other means must be found to prevent spoilage. A low temperature cellar is one possibility, as many types of organisms such as film yeasts and Brettanomyces do not grow well at 55F. Cool cellars are not, however, a good strategy if the intention is not to sterile filter prior to bottling, since activity in the bottle may ensue, resulting in unpredictable results and bottle variation.
II. Nutrients:
Oxygen
Organisms which require oxygen for respiratory metabolism may be controlled by eliminating it from their environment through the use of inert gas and, preferably, by maintaining wine in full containers. These include film yeasts and Acetobacter. Frequent topping, however, has been argued to introduce more oxygen than it prevents, since it breaks the vacuum which builds in a well made barrel. Many winemakers therefore prefer to bung and roll wines which have completed fermentative activity.
Cool cellars, while they inhibit the growth of many organisms, also increase the solubility of oxygen in wine. Oxygen control is not effective against fermentative organisms, including Saccharomyces, Brettanomyces/Dekkera, and malolactic bacteria.
Oxygen is not the enemy of wine. Low oxygen winemaking, while useful for microbial control, is not always desirable from the point of view of phenolic management. Young reds often benefit from large amounts of oxygen to facilitate polymerization and complexation of harsh tannins. Older reds are generally fed oxygen in much lower levels to assist textural and aromatic development without encouraging oxidative microbiology or tannic dryness.
Fermentable sugar
Complete fermentation is an aid in the suppression of fermentative organisms such as Brettanomyces/Dekkera. Dextrocheck or Lane Eynon analysis for residual sugar is not sensitive enough for this determination, and enzymatic glucose + fructose should be run.
Malic acid
Malic and lactic acids can be tracked non-quantitatively (present/not present) by paper chromatography to monitor the onset and finish of malolactic by the simple and inexpensive method of paper chromatography. Enzymatic malic analysis requires a spectrophotometer, but is a wonderful method to monitor progress of malolactic, and is one of many reasons for even small wineries to consider the purchase of an inexpensive "spec," (around $1500). Please refer to the conclusion of the article on urease for a more complete discussion of this notion.
Because it is not microbially stable, I cannot conceive of a situation in which one would consider addition of malic acid to high pH table wine.
III. Inoculum:
Introduction of commercial organisms
We have already discussed the introduction of malolactic bacteria, so I want to confine my comments here to choices about yeast.
Inoculation for primary fermentation with commercial organisms is widely but not universally practiced. Commercial yeasts differ greatly in their fermentation vigor, and slow fermenters such as Pasteur red are popular for red wines since they allow prolonged fermentation on the skins at elevated temperature.
"Wild" or "natural" yeast fermentation simply means that we have not inoculated and do not know what characteristics the fermenting yeast may possess. Some wild fermentations are prone to foaming, sulfide production, vinegar production, high total SO2 metabolism, and sticking. Advocates point to the advantages of sluggish fermentation and the complexity of flavors which occur in these wines.
An idea which has gained recent credibility is that the advantages of both methods may be obtained by reducing the size of inoculum of commercial yeasts. The resulting delayed onset of fermentation allows natural non-alcohol tolerant yeasts such as Hansenula and Kloeckera to add complexity at the beginning of fermentation, still allowing the commercial yeast, with its predictable characteristics, to finish the fermentation. This strategy may be of particular interest to organic winemakers.
Sanitation
Wineries are not sterile environments. Spoilage cannot be prevented by maintaining an environment free of microbes. Most wineries of any age have indigenous populations of Saccharomyces, Brettanomyces, film yeast and malolactic bacteria. Care to minimize populations by reasonable sanitation procedures is nevertheless the policy of most California wineries. Less so in European cellars, where indigenous microbial populations have stabilized and a "gout de maison" or house flavor profile, which has developed over centuries and whose evolution and control has been empirically incorporated into cellar practices, may be a valued element of the wine.
Since no human pathogen can live in wine, winemakers can afford to be much more blase about sanitation than other food producers. In high pH winemaking, the goal is often to allow the wine to undergo all potential microbial activity at the winery , and sanitation should be considered in this context. For unfiltered products, a warm cellar (60-65F) which promotes potential activity, may be a wise choice.
Because of its alcohol and acidity, even high pH wine is an unusual environment, and most organisms cannot grow in it. Contact with sewage, for example, is less of a threat to wine spoilage than contact with pockets of spoiled wine. The importation of bulk wine, used barrels, and wine containing equipment should always be focused on as an event which might introduce a virulent strain of spoilage organism such as a particularly active film yeast or Lactobacillus.
Filtration
I like to define winemaking as "the art of intelligent compromise." Filtration decisions balance flavor loss against in-bottle spoilage in the context of a particular wine. Some wineries filter their cabernet but not their pinot noir, for example. Some decisions, such as sweet wine bottling, are pretty straightforward: filters are better than sorbate and cheaper than high-tech pasteurization.
In high pH winemaking, the key to bottling without filtration is to eliminate the nutrients listed above from the equation by provoking microbial activity at the winery.
SECTION 2: PHENOLIC CHEMISTRY
Red wines are distinguished from whites, more or less, by the introduction of several hundred species of phenols during primary fermentation on the skins.
Monomeric phenols contribute to aroma, while polymeric phenols (tannins) are responsible for astringency.
Winemaking philosophy has progressed considerably over the last twenty years regarding texture goals. It is now clear that gross amounts of tannin per se do not promote long ageing, since the reaction of tannin with oxygen is very slow. Wines thought to be soft and wimpy in the 70's, such as the early Jordan and Veedercrest cabernets, have aged magnificently, while their "bigger" counterparts remain harsh and unappealing. At the same time, the expanding red market has reflected its desire for less tannin in burgeoning sales of merlot over cabernet. California winemakers are now less obsessed with trying to extract "guts, feathers and everything," paying more attention to the French notions of quality. At the same time, full extraction strategies are learning to incorporate sophisticated cellaring techniques to manage texture.
The Bordolais speak in terms of ripe, short chain "soft" tannins as a goal for red wine texture, and also assert that these should form complexes with anthocyanin pigments to produce stable color and soft rich mouthfeel. Adequate tannin extraction to promote this complexing is thought to require fermentation at elevated temperature (over 80F), and may be enhanced by extended maceration for up to several weeks post fermentation.
Ripe fruit is essential for this kind of wine, and in many California vineyards may only be maximized at elevated brix as in France, and green tannins are a particular problem for uneven ripening varieties such as zinfandel. For this reason, many wineries are now allowing extra ripening, then removing excess alcohol with spinning cone and reverse osmosis technologies.
Layers of soft tannins may be encouraged by blending and even by co-fermentation of complementary varietals. Selective extraction strategies, those that attempt to extract the maximum monomer and leave behind the gross tannins, can be implemented at several production stages. Choices include crusher design, cap management technique, yeast selection, fermentation temperature and duration, press type and method of operation, fining regimen, and barrel manufacture.
The French notion of elevage (to "raise" the wine as one raises children) includes many approaches to enhancing tannin structure which include micro-oxygenation (to build structure, round tannins, integrate aromatics and quench reductive proclivities), periodic macro- oxygenation (to open and advance the wine's ageing) and lees contact. The timing and levels employed are critical to success with these techniques.
The rich finish of a classic bordeaux is not entirely attributable to phenols. Potassium and sulfate both contribute the back palate mouthfeel, and are natural by- products of high pH winemaking. Sulfate is the product of sulfite oxidation, which occurs much more rapidly at high pH. Potassium is the counter-ion in the highly buffered solutions typical of this genre. High pH wines are typically not cold stabilized since this results in lowered potassium and higher pH.
Cold stabilization may be useful, however, to reduce high TA in wines of the central coast, whose acid taste creates the impression of harsh mouthfeel. It should be kept in mind that while cold stabilization lowers pH if it takes place below pH 3.6, in the high pH realm it always raises pH.

Тук има преводач, за неползващите англииски
http://webtrance.skycode.com/?lang=bg

Искат някой лев, ама то без пари само sstan работи за тоя форум :D
vinoirakia
 
Мнения: 363
Регистриран на: Сря Фев 28, 2007 12:29 pm
Местоположение: Пловдив

Мнениеот adam40 » Пет Ное 28, 2008 2:32 pm

Защо виното, което е буре малко се обезцвети за разлика от бидонче от мин. вода?
adam40
 
Мнения: 1
Регистриран на: Пет Ное 28, 2008 1:45 pm
Местоположение: s. Joakim Gruevo

Мнениеот vinoirakia » Чет Ное 05, 2009 8:25 am

То вместо 1 седмица мина 1 година и отгоре.
По-възрастното поколение технолози гледат повече общите киселини и много не ги интересува рН.
Работил съм в голям български винпром/приемал по 12-20 млн. кг. грозде на кампания/ - 2002 нямаше рН метър. И виното се е продавало и пак са приемали.
По-младото поколение стриктно следи рН без да гледа Общите Киселини.
Кой къде е? Сам да си прецени.
Та това беше АК-47 срещу Колт М-16, рН срещу ОК/ТК/, един начин на работа срещу друг.
Ето една помощна статия

The pH of must and wine has a profound influence on winemaking practise and wine quality. High quality winemaking should not be ignorant of this winemaking variable. The following article outlines the ways in which varying pH values influence wine and the issues surrounding winemaking. It also notes the influence of pH on various taste factors, typical pH aims in wine types and expected pH increases/decreases during winemaking.
Influences of pH on wine
pH contributes to wine in a number of ways. These are listed below, with a low pH affecting wine in the following ways:

SO2 is more effective as an antimicrobial agent
Favours the most desirable types of lactic acid bacteria (LAB)
Increases microbial stability through increased inhibition of bacterial growth
Enhances production of fruity esters during yeast fermentation
Generally speaking, yeast ferments less efficiently
Shifts colour equilibrium to more red pigments
Increases colour hue
Provides a fresher taste
Increases monoterpene (geraniol, citronellol and neral) concentrations
Increases ageing potential

pH and taste
Sourness: Acid sourness is independently influenced by the concentration, pH, and anion species of acid [Sowalsky and Noble, 1998]. A lower pH at the same titratable acidity (TA) gives more sourness.

Astringency: This is defined as a persistent sensation, increasing upon repeated ingestion. Astringency is affected by pH - as pH increases, astringency decreases [Noble, 1998; Peleg and Noble, 1999].

Bitterness: pH has little or no affect on bitterness [Noble, 1998].

Mouthfeel: higher pH's tend to give a rounder, softer, mouthfeel.

Polymerisation: the higher the pH, the slower the polymerisation and the more unstable the colour.

Volatile acidity: more volatile acidity is produced by yeast at lower pHs.

Acid types and pH
Within the usual pH range of wine, tartaric acid is more highly ionised than malic, which is inturn more so than citric. Tartaric will liberate the most H+ ions yielding a greater shift in pH. Thus, adjusting TA with tartaric causes a larger shift in pH than an equivalent quantity (same TA shift) using malic or citric being added. For maximum pH adjustment with a minimum accompanying TA increase, use tartaric.

pH aims
The typical pH aims for given wine styles are as follows:
Final pH of white wine: 3.0-3.3
Final pH of red wine: 3.3-3.5
Optimal pH before a MLF: 3.2-4, >2.9
It should be noted that these are typical values only. Deviations may be expected and should not necessarily be seen as a problem.

pH's higher than 4.0 are generally avoided as spoilage is more likely to occur above this level. (The optimum pH for bacterial multiplication is 4.2-4.5.) Many winemakers keep wine pH below 3.65. Many winemakers tend to ignore TA and acidify/deacidify based on pH only. This may be a practical approach when working with quality fruit that is typically high in pH and low in acidity, however it can be unwise to follow this approach in other cases. There is a trend, particularly with warmer climate fruit, to acidify musts in order to bring down what are seen as excessively high pH's (generally > 3.65). The corresponding increase in TA should be noted and kept in check (at least by tasting the must/wine). Surely it is preferable to produce a high pH yet drinkable wine to a lower pH wine whose TA is so high it is difficult to drink?

Typical pH increases/decreases
Addition of acid: Wine is a highly buffered liquid. This means that the corresponding pH decrease for a given addition in TA (added acidity) is not directly proportional. Further, the change in pH for a given TA increase/decrease is unique to each individual wine, since every wine is buffered slightly differently. However, as a general rule, the addition of 0.5-1 g/l acid as tartaric tends to drop the pH by about 0.1 units.

Maceration/pressing: These operations may result in an expected pH increase of 0.05-0.2 units. This is due to the leaching of potassium in the grape (/fruit) skins.

Fermentation: Following fermentation of tartaric-dominant grape wines, an increase in pH of 0.1 unit may be expected. Note that in the case of non-grape wines inwhich tartaric is not a dominant acid, a significant increase in TA and a corresponding decrease in pH may be expected during fermentation.

MLF: Following MLF an increase in pH of 0.1-0.3 units may be expected.

Tartrate precipitation: The precipitation of tartrate (requiring the presence of both tartaric acid and potassium) can cause pH shifts either up or down. It is important to note that there is a pH point around 3.6, above which tartrate precipitation causes a pH increase and below which tartrate precipitation causes a pH decrease. The point varies from wine to wine but generally occurs between pH 3.5 and 3.7.

pH and titration
Titratable acidity is determined analytically by titration. Titratable acidity is not the same as "total acidity", which is defined as the equivalent number of protons that the organic acids would possess if they were not dissociated. Titratable acidity is no more than a measure of the hydrogen ions required to obtain a specific pH end point, and is always lower than total acidity. The standard titration method advocated by the Office International de la Vigne et du Vin (OIV), and used in France, titrates to the endpoints pH 7. Whilst the method advocated by the Association of Official Analytical Chemists (AOAC), used in the United States and elsewhere, titrates to the endpoint pH 8.2. Given that the dissociation of the organic acids present in wine is weak, neutralisation with NaOH (the common strong base used for acid titration) is likely to occur above pH 7. For this reason, titration to the pH 8.2 endpoint is considered more reasonable. It should be noted that the calculated TA value of the same wine will be different when using a different pH endpoint. Having titrated to a pH 7 endpoint and calculated the TA, the equivalent TA for a pH 8.2 endpoint may be calculated based on the following equations (Darias-Martнn et al., 2003):


TApH7=0.975xTapH8.2 - 0.436 (red wine)

TApH7=0.962xTApH8.2 - 0.247 (white wine)

To determine the TA, titrate to the respective pH and calculate as follows:

75xNxV
TA=-------------
S
where:
TA is the titratable acidity (g/l as tartaric),
N is the molarity of the NaOH,
V is the volume (ml) of NaOH required to titrate to the endpoint,
S is the volume (ml) of the sample titrated.

References
Darias-Martнn, J., A. Socas-Hernбndez, C. Dнaz-Romero and E. Dнaz-Dнaz. 2003. Comparative study of methods for determination of titrable acidity in wine. Journal of Food Composition and Analysis, 16, 555–562.

Noble, A.C. 1998. Why do wines taste bitter and feel astringent? In Chemistry of Wine Flavor (ed. A.L. Waterhouse and S. Ebeler ) ACS Symposium Series #714, Amer. Chem Soc. Washington, D.C. pp 156-165.

Sowalsky, R. A. and A. C. Noble. 1998. Effect of the Concentration, pH and Anion Species on the Sourness and Astringency of Organic Acids Chem. Senses 23 (3) 343-350.

Peleg, H. and A.C. Noble. 1999. Effect of viscosity, temperature and pH on astringency in cranberry juice. Food . Qual. Pref. 10:4-5, 343-347.

Толкова от мен.
Новия свят гледа сляпо рН, но и гроздето им изва с нормални показатели.
Не ги спира да коригират, докато виното стане перфектно за цената си.
vinoirakia
 
Мнения: 363
Регистриран на: Сря Фев 28, 2007 12:29 pm
Местоположение: Пловдив


Назад към Въпроси и отговори

Кой е на линия

Потребители разглеждащи този форум: 0 регистрирани и 1 госта

cron